REFERENCES

1. Алмазова Н.И. Academic Writing. Учебно-методические рекомендации для магистрантов и аспирантов: учебно-методические материалы / Н. И. Алмазова; Санкт-Петербургский политехнический университет Петра Великого. – Спб, 2019: Режим доступа – <URL:http://elib.spbstu.ru/dl/2/s19-124.pdf>.
2. Английский язык. Практический курс для магистрантов технического профиля: учеб. пособие / Н.И. Алмазова [и др.]; под ред. Акоповой М.А. – СПб. : Изд-во Политехн. ун-та, 2013. – 290 с.
3. Н.К.Рябцева. Руководство по научному изложению. Словарь оборотов и сочетаемости общенаучной лексики.-М., Изд-во «Флинта», Изд-во «Наука», 1999г.
4. Alice Oshima, Ann Hogue. Writing Academic English. Fourth Edition.-USA,2009.-337 pp.
5. Anil Kumar S, Mahendra Babu N C. Influence of Induced Residual Stresses on Fatigue Performance of Cold Expanded Fastener Holes. 5th International Conference of Materials Processing and Characterization (ICMPC 2016), 2016.
6. Bert Blocken, Thijs van Druenen et al. Aerodynamic drag in cycling pelotons: New insights by CFD simulation and wind tunnel testing // Journal of Wind Engineering & Industrial Aerodynamics 179 (2018) 319–337, 2018.
7. Bortyakov, D. E., T. I. Uzunov, O. L. Alipiev, E. I. Bargazov, (2017) Studing the elasticity of the units of the level luffing jib system in gantry cranes using MATLAB. IN: Modern mechanical engineering: Science and Education MMESE-2017: Proceedings of an International Scientific and Practical Conference, Russia, St. Petersburg, June 22-23, 2017, Publishing Polytechnic University, 2017, pp. 746-756, ISBN ISSN 2223-0807.
8. José M.C. Azevedo*, André Cabrera Serrenho, Julian M. Allwood, Energy and material efficiency of steel powder metallurgy// Powder Technology 328 (2018) 329–336, 2018.
9. Luka Sterle, Mitjan Kalin, Franci Pusavec. Performance Evaluation of Solid Lubricants Under Machining-Like Conditions // 8th CIRP Conference on High Performance Cutting (HPC 2018), Procedia CIRP 77 (2018) 401–404, 2018.
10. 10. Manzhula, K.P., Naumov A. V. Influence of Flections’ Radius Value to Local Buckling of Box-Shaped Beams with Non-Linear Walls // International Review of Mechanical Engineering (IREME), Vol. 11, N. 5. ISSN 1970-8734 May 2017, Special Issue on “Advances in Modern Mechanical Engineering Research”, 2017.
11. 11. Manzhula, K. P., Shlepetinskii, A. Yu. Stress and Strain Concentration in Weld-Joint Flaws // ISSN 1068-798X, Russian Engineering Research, 2016, Vol. 36, No. 9, pp. 722–726.
12. 12. Mohd. Nayab Zafara, J. C. Mohantab. Methodology for Path Planning and Optimization of Mobile Robots: A Review// International Conference on Robotics and Smart Manufacturing (RoSMa2018), 2018.
13. 13. Qinyang Zhao, Fei Yang, Rob Torrens, Leandro Bolzoni. Comparison of hot deformation behaviour andmicrostructural evolution for Ti-5Al-5V-5Mo-3Cr alloys prepared by powder metallurgy and ingot metallurgy approaches, // Materials and Design 169 (2019) 107682, 2019.
14. 14. Renhui Zhanga*, Junhu Yanga, Rennian Lia. Parametric Control of the Hydraulic Machinery Impeller Based on Free-Form Deformation // International Conference on Advances in Computational Modeling and Simulation, Procedia Engineering 31 (2012) 909 – 913, 2012.
15. 15. Tiziana Segretoab, Alberto Bottilloa, Alessandra Caggiano, Massimo Martorelli. Integration of reverse engineering and ultrasonic non-contact testing procedures for quality assessment of CFRP aeronautical components // 12th CIRP Conference on Intelligent Computation in Manufacturing Engineering, 18-20 July 2018, Gulf of Naples, Italy, 2018.
16. 16. Shestopalov A., Boitsev A. Methods for Evaluation Structural Anisotropy of Asphalt // International Review of Mechanical Engineering (IREME), Vol. 11, N. 5 ISSN 1970-8734 May 2017. Special Issue on “Advances in Modern Mechanical Engineering Research”, 2017.